Mods for ALL Stacked-Tube Blow Back Markers (Spyder's and Clones)
Instructions for these modifications can be found at
OtterSC Customs and the
Spyder Forums, but by having the mods done by myself, you get a
Money Back Guarantee. Also,
all prices are firm, no exceptions, but trades are still welcome.
It has come to my attention that these mods basically give you the Spyder SE Valve System. They work the same way, and on the same principal.
Venturi Removal................- $0.50
Custom Spring Spacer..... - $0.75
Trigger Shim Job...............- $1.00
See Sear Shim Job
Sear Shim Job...................- $2.00
Polished Hammer..............- $2.50
See Ultra-Lite Hammer
Polished Sear....................- $3.00
Polished Bolt (metal only).- $3.50
See Ultra-Lite Hammer
Trigger Pre-Travel Adjust..- $4.00
Trigger Post-Travel Adjust- $4.00
High Flo Valve...................- $5.00
comming soon
UL Trigger (Egrip only)......- $5.00
Magna Trigger (Egrip only)- $5.50
High Flo Vertical Adaptor...- $5.50
comming soon
High Flo Valve Pin..............- $6.50
Still in design process...
Add PSI Gauge
*................- $7.50
Hair Trigger (mech only)
**.....- $10.00
Ultra-Lite Hammer
***............- $10.00
Still in design process...
Parts Test****......................- $1.50
General Maintenance*****..- $5.00
LP Tuning******..................- $20.00
Now, with my personal setup (Spyder Imagine), My marker works at about 200-300 psi, and that’s a HUGE improvement over stock. Stock Spyders I believe work at around 800 psi, so by getting the psi needed to operate you marker lower, you gain efficiency, and a lot of it!
STBB Mod Rules:
- I will NOT pay for shipping, you must cover it BOTH ways
- I will NOT refund money if your marker still functions with these mods
- Turn Around time is approx. 1-20 business days, depending on the (amount of) mod(s), and may take longer. Nothing is set in stone.
-
*You can ship and provide your own gauge (1200 or 1500 psi rated for CO2 usage, 500-1200 psi for LP or HP HPA/Compressed Air tanks, and 400+ psi gauge for LP, only) with your marker, or I can buy a 1200 or 1500 psi gauge for stock, or 400+ psi gauge for LP, of my choice (model and size may vary) for an additional $18.00 (the cost of buying AND shipping a gauge to me)
-
**Because the Hair Trigger mod minimizes the surface area the sear actually makes contact with the hammer, there is a greater possibility that the sear will fail faster than if left stock. Polishing the sear will fix the problem untill the sear wears down again.
-
***By reducing the mass of the hammer, inertia is lost, less force strikes the valve pin, causing a FPS drop. To counteract this, I suggest buying a Spring Kit, or one of my Spring Spacers
-
****I CAN test the items before sending back, depending if you send me your entire marker, or if the parts will fit my Spyder Imagine
-
*****General Maintenance includes a complete disassembly, complete cleaning of
all parts, replacing all damaged or worn o-rings and/or seals, relubing, reassembly, and a free
Parts Test.
-
******LP Tuning can only be achieved after Venturi Removal, Polished Hammer and Bolt, High-Flo Valve, Valve Pin, and Vertical Adaptor, Ultra-Lite Hammer, the purchase of an aftermarket reg with a gauge at 400+ psi, or my PSI Gauge, and a Spring Kit. After obtaining all of the mentioned in some way (most/all can be bought aftermarket), I can tune your marker to the lowest psi while still maintaining the fps you desire aslong as it stays at or below 300 fps.
-
I will ONLY repair/refund money if you give me solid proof (possibly video, could be something else) that your marker functions incorrectly
-
If I unintentionally damage any part of your marker, I will notify you immediately so we can work out getting you a new part or something else
-
All modified parts are under a 30 day limited warranty from the time I ship out. If any part of my mods should break, fail, or stop functioning under normal play, feel free to send it back to me for free repairing or replacing, or ask for a refund
-
Warranty does not cover surface damages (nicks, scratches, etc), misuse, abnormal use, useing parts other than it's designed purpose, improper assembly, disassembly, re-assembly, or any further modifications attempted by anyone else besides myself (TheAznInvazn).
Payment Options and Conditions
See below or above