Thread Tools

**micflint001** · June 28th, 08:34 PM

ok i am going to get a mag body and i need to know what are the main internals you need for the mag(like bolt ex)thanxs i wll greatly appreciate any help

**normalperson97** · June 28th, 08:56 PM

you will need a valve: for this you could get an x-valve, retro valve, classic valve(the bolt should come with the valve that you get),
trigger frame:you could get the regular single trigger one, benchmark, intelliframe, or a dye trigger frame
sear and trigger rod,
rail
and barrel(any one you choose but may depend on threads because of body)

sslecyk03 · June 28th, 09:23 PM

dont forget the sear pin

**micflint001** · June 28th, 10:22 PM

ok so is that all? another question i think i might get a automag body and build up from there but the body i want doesnt have a feed tube its just a hole lol what can i do about that?

**normalperson97** · June 28th, 10:24 PM

you can buy a feed neck, but first you have to find out what kind of threads it takes

**micflint001** · June 28th, 10:26 PM

oh so the neck that you put the painit in right? you screw it in (im sorry im used to spyders lol)ok and um what is a good website i can get all the parts at?

sslecyk03 · June 28th, 10:40 PM

it would probably save you the time and money to just buy a ULE body, u can probably find a used one on EBAY or in the b/s/t threads on different forums. Otherwise you will need to find out the threads and i doubt there are that many aftermarket feed necks for mags, if any at all. If you happen to find one, apply a lil loctite on the threads and screw it in with a strap wrench. All of the parts needed, besides the feedneck, can be bought at AGD's website, airgun.com i think.

**micflint001** · June 28th, 10:47 PM

here is the body http://cgi.ebay.com/ws/eBayISAPI.dll...685478842&rd=1 its on ebay and im thinking about getting it so now is it the screw in feed neck or what? i appreciate all your help man

sslecyk03 · June 29th, 01:42 AM

o i know what that is, its milled from a sluggo( a body bought from AGD to be custom milled). Its called an IT body. Pretty sure it takes angel feed neck threads and angel detents, barrel threads are cocker. This means there are alot of feednecks that will fit that body. Probably try to get a twister.

**normalperson97** · June 29th, 07:30 AM

you're right about angel threaded feed neck but it says that it uses 3/8 inch cocker detents

**anxiouspaintblr** · June 29th, 08:10 AM

So your just buying a body? Or do you have the trigger too? Cause you only asked what goes into the body...

Into the body is just a valve. I would suggest this one for the BEST performance:
http://www.airgun.com/Products/xvalve.shtml
If its a lil outta your price range just get a retro or something cheaper.

As for a trigger I would get this:
http://www.airgun.com/intelliframe.shtml

As for the for grip I dont know what to tell you cause I have an E-Mag and the battery just sits there.

**micflint001** · June 29th, 11:00 AM

do you think it would be cheaper to get a rt pro than to start from the ground up?
thanxs again for all your help i appreciateit

**anxiouspaintblr** · June 29th, 11:05 AM

Ummm I would probably say yes...but it would just be stock. No intelli or anything the valve isnt AS good as x valve but its still good enough for what youd be shooting. If your worried about it being hard to put together its not. Mags are so simple. and we can always help you out if you dont know how to fit something or whatever other problems you have.