Thread Tools

BichSlapinWorr · June 17th, 07:55 PM

Well my B - day is slowly approaching, july 20th (yay for me) and i am going to have some b day money thrown at me. Ill give you a list of what i have already and then you can give me Tips on what to get next.

Its basically all stock...
2k3 orracle
Worrblade + bolt
CP On/off
68/4500 Pure Energy
Eggy/Z board- Cut and Shaved
Stock Orracle Ram and Lpr
Stock Kaner barrel

**E-99 king** · June 17th, 08:10 PM

There really isnt much you can do to that. Maybe get some trv's for your ram and maybe a hybrid eye cover to raise the cool factor.

**macdaddy** · June 17th, 10:03 PM

If you have to spend money on something u could get a halo, there isnt really a point but if for some reson you neaded to shoot over 17 bps you could. Or you could get a samurai trigger.

**lightbulb8817** · June 17th, 10:12 PM

buy a half dozen cases of paint.

**PaintBallBob** · June 17th, 11:07 PM

spend the money on playing
you cant reallly upgrade that too much more

**CoolHipJim56** · June 17th, 11:10 PM

If you dont have a good mask, i would recommend that. Otherwise, do as PaintballBob said, and spend it on playing.

**andy_5187** · June 17th, 11:10 PM

samuri trigger, free flow valve i get about 3000-3500 shots off a 88 ci 4000 psi fill. which is insane... paint, eyecover, backup gun just in case

BichSlapinWorr · June 18th, 09:50 AM

Yeah i was looking into the free flow valve, but is my Ram ok? shouldnt i look into maybe a free flow or eclipse with Qev's? I also want to get a Custom Shroud off of docks machines

... there has to be something. What about a barrel kit.

**bob005** · June 18th, 09:56 AM

palmers microrock lpr, and an ff ram w/ qevs...but then again, thsoe are only slightly better than the ones you have, and it isn't worth putting that much money into for such a slight difference

**Cerebeus** · June 18th, 09:57 AM

Yes, barrel kit. I think these people assumed you meant a Kaner KIT when you said Kaner barrel. Get a barrel kit..

BichSlapinWorr · June 18th, 10:00 AM

Could i fit QEV's on my ram?

**The nforcer2006** · June 18th, 10:25 AM

Yuo can put a qev on your rear port, but you have to get TRV's for your sto.

**imhungry** · June 18th, 12:38 PM

the ONLY thing i would replace is the ram and the bolt. get a .44 magnium ram w/ QEV's and a really light bolt. the orracle bolt is nice, but its heavy. since you are getting a worrblade, you have the bolt covered. if you are REALLY anal about low cocking mass, you might want to look into a super light back block (also super ugly) like the slik. honestly, i dont think they are worth it

**DemoCommando** · June 18th, 01:38 PM

I'm getting my Worr Bladed Orracle next week, I ordered from a guy off pbn, he had great feed back and he only used it for 5 days then is selling it. I also have other stuff and will be looking for ups.

It is

-Factory Installed Worrblade kit w/ ACE
-ANS Quick RAM
-Qty. 2 One Piece pump arms.
-Qty. 1 Clippard QEV & Qty. 1 Planet Eclipse QEV
-Worrblade Bolt
-Orracle Bolt (Chrome back & Red Delron tip)
-WGP Torpedo Drop Forward
-WGP Hi & Low Rise
-72/4500 Crossfire Stubby

I'm ordering BZ's evil pipe, Kapp Ball Detents, a new cocking rod(shocktech), and clamp feed.

But what else should I get?
FF Valve, .44 Mag Ram, what else now? Just leave as is?

***NYY*** · June 18th, 01:42 PM

i would say get money to just play, or ask for a gear bag and stuff like that. i dont see how you can be dissatisfied with that setup

**DaBluedevil** · June 18th, 02:29 PM

*****slappinworr - I have hte same gun as you do(about), here are what I would do:

Barrel Kit - Personal preference on this one
HaloB with victory/Ripdrive
TRV Kit
Clamping low rise(Convience)
Samurai Trigger

If you wanna get every drop of performance, keep reading.
CCM Straight cocking rod
Slik kit
FF Internal kit

**imhungry** · June 18th, 05:54 PM

the ans ram sucks dude, get the .44 magnium or the FF ram. the ff internals are not necessary. the WGP ones are basiclly the same and there is no need to replace them. when i got my FF internals, the hammer had a huge mechining gouge in it so i just poped the worrblade lockdown hammer in and i actually get better efficiency

BichSlapinWorr · June 18th, 06:39 PM

I already have the worrblade, and the bolt. I will get the the .44 eventually, with QEV's. Im not exactly used to walking the worrblade so im not buying a halo yet. It would just be a waist im not pulling the trigger fast enough ( for me the worrblade trigger doesnt have enough bounce, i walk it and the trigger isnt even coming back ) . Im going to get a CCM no rise, and a barrel kit. And i might even get the FF valve, i have talked to people on this forum who have em and they say they are efficient as hell.

**imhungry** · June 19th, 12:36 AM

ff valve is the exact same thing that u have in there now. total waste of money. the FF spring kit would be the only thing worth buying out of the FF internals. also, eblades have the most bounce out of any frame i have used. adjust your tpul and return settings a lil bit.

**DaBluedevil** · June 19th, 08:22 AM

How to get bounce-
Turn on gun.
Open Grip frame(Right Side)
Hold red button untill the timing menu comes up.
Go into Filters
TPUL
Set it to 2
TREL
Set it to 1

Shoot gun, test. If it has to much, adjust as necesarry. First I would suggest adjusting your trigger to exactly how you like. You can also adjust your cdel time to help 'smooth' out the gun up to almost 9 ms. That's if you want, I haven't touched my cdel.