Thread Tools

**EverLong** · August 27th, 06:53 PM

My viewloader won't work. Everytime i attach the co2 tank to the gun, i don't hear the hiss or anything and when i try to shoot, none of the air comes out. Please help

**Xx50NuTSxX** · August 27th, 07:06 PM

i dont know **** on viewloaders but umm, your tanks screwed in all the way and your cocking the bolt back right?

**EverLong** · August 27th, 07:14 PM

**Xx50NuTSxX** · August 27th, 07:20 PM

aight try lathering up the bolt.. and when you screw in the tank does it gas up? and also drop some drops in the asa, and let it go through the macro and stuff, then try it

**EverLong** · August 27th, 07:34 PM

sorry i'm such a noob. What's an asa and a macro?

FearTheCocker · August 27th, 07:54 PM

start off the asa is where you connect the tank to your gun, and the macro line is the line running from your asa, also check and see if your bolt is upside down if that is the case then just turn it the right side. And is your tank full if it isnt it aint going to shoot.
And finally vl guns suck plainly sell it to some homeless guy 4 like a bottle of spirits or some bottle caps and save up and get a spyder, tippmann, or pirahna

This isnt that robbie kid that paintballs w/ joey and jim is it cause if it is i lit you up so bad ahahahahahahaha

**Smitty** · August 27th, 08:12 PM

try pushing in your tanks pin with a car key or coin, tell us if you get a hiss

Alpha · August 27th, 08:17 PM

Smitty, I'm onto you. Dude your tank could be empty and you might have to refill.

**Smitty** · August 27th, 09:04 PM

Actually I have seen a tank that was full but you couldnt push in the pin even by screwing the tank on. I think it was over filled or something cuz we bled off some pressure via the burst disk and then it worked.

**MP11** · August 27th, 09:21 PM

i saw that happen last week, the valve was busted, didnt let air in our out. that could be the problem.

**EverLong** · August 27th, 09:25 PM

So what should i do?

**MP11** · August 27th, 09:27 PM

go to your nearest pro shop and explain the problem. they determine what the problem is.

**TheConMan41** · August 30th, 04:23 PM

MP11 has the right idea. Smitty's way can determine what might be wrong with it, but you never go wrong with a proshop.

FearTheCocker · August 30th, 07:26 PM

if there is a hole in your burst disk like most tanks the pressure should lessin and it should b able to b workin in awhile it must have not been over to filled cause it would have flew off it was

**ViolentJ333** · August 30th, 08:05 PM

Take it outside, put the co2 tank on a fire. If no response firmly grasph the barrel and through that ****er as far as you can!

FearTheCocker · August 30th, 08:09 PM

Quote:

Originally Posted by ViolentJ333

Take it outside, put the co2 tank on a fire. If no response firmly grasph the barrel and through that ****er as far as you can!

wow great sarcasm yea its a vl but were talking about a co2 tank the only problems w/ the gun would b the bolt upside down, clogged line or the sear or somethin is ****ed

do this test take the oring off and put it in hte gun might do somethin idk

violentJ your a noob stfu

ckkk requesting the d bomb 4 a neg point on him

**silentgun** · August 31st, 07:37 PM

You can write vewloader and explain your problem

**skx762** · September 1st, 02:52 PM

It's a pretty simple design, can't be too much wrong. I have one and it is easier to work on than my Triton or Prodigy. Please keep us updated.

**Number One Andrew** · September 2nd, 04:56 PM

Does the bolt move at all? It just sounds like you didn't oil the CO2 o ring, that happened to my Triton back when I was a n00b. I just oiled the o ring and all was well.

Thread Tools

View more Paintball photos