Thread Tools

**FASTnSPEEDY** · July 16th, 12:05 PM

I just got my tes yesterday and I have 2 problems with it.

1. After shooting the TES sometimes it will only get half the way back to being cocked. (It's not recocking)

2. It's double fireing, I pull the trigger and It fires 2-3 shots immeditley, and breaks the last ball of the 2-3 it shot. (I have a gravity feed hopper)

3. After it breaks the ball it blocks the eye and then it will not shoot untill I turn off the eye, or clean the gun out.

Thanks for all the help,

John.

**20bps_tes** · July 16th, 07:03 PM

try a light main spring and streaching the sear spring abit! also make sure the marker is oiled and dont have the psi over 400

**pball4sissies** · July 17th, 05:00 PM

wow..wait..this gun is a HP gun right? no LP? o_O;

**20bps_tes** · July 17th, 06:23 PM

the tes is a lp gun 500 and under = LP

**dirtrider54** · July 18th, 02:31 AM

yeah mine runs at like 250.... perfect fps.... make sure its down.

**FASTnSPEEDY** · July 20th, 05:41 AM

I'm a newbie to owning mown gun so bear with me,

where exactly do you oil, and how much?

What kind of oil?

The guy that works on guns at the feild I sometimes play said pbguns shoulden't need to be oiled.

themainevent · July 20th, 02:54 PM

blowbacks always need oil, i had to grease down my old amg after a half a case. I used goldcup, but any oil made specifically for paintball guns should work. Now the guy you were talking to may have been talking about higher end guns, in which most use lube

**|AC|METAL|** · July 20th, 03:51 PM

yah any oil will work, although i use lube (dow33) and i'd lube (or oil) the stock bolt and make sure it is at all times, and get a faster loader man its like puttin that gravity feed loader of yours on an angel, it just wont do it.

**FASTnSPEEDY** · July 21st, 02:10 PM

Yeah I will get a good loader, as soon as I get some money. (It could take a while)

When you oil it you put ten drops of oil on each of the O Rings in the bolt?
(I'm totally guessing)

**Warpstoner** · July 21st, 02:31 PM

You don't need ten drops, just enough to cover the o-rings.

Make sure your TES isn't on 3-round burst. That could be the reason why its shooting a few times each trigger pull.

**|AC|METAL|** · July 21st, 05:03 PM

BURST??!! what TES is it i dont think the TES has any burst man not even the TES B

**Warpstoner** · July 21st, 06:41 PM

Ok, just making sure.

**StealthRT** · July 21st, 06:56 PM

If you unlock all the fireing modes you get "multi" with is the same as burst...

Put 2-3 drops of oil on each oring of your bolt. Use PB gun oil, alot of other oils will swell orings and in most cases thats a bad thing...

Also remove your stock SS hose from the regulator, and drop about 5 drops of oil into the bottem of the regulator. Our stock regs DO NOT come lubbed from the factory, and it will be tons more consistant if you lube it up before you play. When you do this, turn the pressure all the way down before you apply air to it again...If you have it set at 300psi before lube, it could jump drasticly after its lubbed up and working good...Most TES's run in the range of 200-300psi, so don't get excited with your pressure...Also the stock gauge is very inaccurate, so don't trust it...chono your gun before you decide to shoot anyone with it...

And I would reach out and slap anyone who said paintball guns shouldn't require any oil...definatly fire him from a position where he gets to work on guns...ooch...

**FASTnSPEEDY** · July 22nd, 11:28 AM

Thanks for the help, StealthRT that helped me a TON!

I will get my gun out later and put 3 drops or PB oil on each of the O-Rings in the bolt, then 5 in the bottom of the regulator.

**FASTnSPEEDY** · July 22nd, 03:45 PM

One last question, I don't have any pb gun oil, but my brother bought and Tipp. A-5, Is it ok to use the oil that came with his gun?

Thanks so much!

**StealthRT** · July 22nd, 04:59 PM

Yep that should work just fine.

Thread Tools

View more Paintball photos