shibbyPB2X

hey I bought a tessy barnd new and loved but then I started to have problems I upgraded with a shocktech supafly bolt painted the handles black and it still is having problems with the ball curving and chopping paint I dono why because I have and eVLution egg hopper loads 23 bps but I'm using co2 can't afford the nitro I don't know if that's my problem or not but even if it was and I could afford the nitro I'd have to buy a new drop forward cause nitro tanks won't fit with the dragun stock drop forward any ideas thanx

onesikpup

id say either you are shooting hot (velocity too high) or you have a poor paint to barrel match. maybe even bad paint.

__________________
FEEDBACK

Hobo_Joe

**POP** sorry had to burst ur little bubble.... but you can have a nitro tank on a tessy, just not one with a big gauge (crosfire for eg).

Any ways in 20bps's sig there is a link to the Dragun owners forum. On there I read that if the bolt is too far back from the feed neck it will burst balls, the guy who wrote that sugested putting an extra o-ring on the ram rod.... I dont know if it works. Also an egg only feeds 17-20 MAX

__________________
Marker = Dragun "The One". #19

=-if you followed these instructions you do so at your own risk, Hobo_Joe, the author takes no responsability for your stupidity in listening to ppl on the internet

Please rate my T1

shibbyPB2X

no an egg with an upgrade Z-board will load 23 but thanx for the help

__________________
04 Bonez LCD
egg II
14 pmi razzor barrel

soon 2 hav:
pmi 48/3000 n2 tank (aim me on pbnotoriousBAC if u sellin 1)
shocktech bolt

ToridXFast

do you have the eyes on or are they coverd in paint you may wanna take them out and clean them then i would check the velocity and set it at about whatever is recommended for the field then make sure you have it turned up the( the number of bps on the board that you are shooting) for example it is preset at 15 turn it up to like 18-20 and see what happens

shibbyPB2X

well I used it today and it worked great don't know what I did diff but I keep the eyes off because they don't see some paint and my loader can load faster than gun I dono how to turn the manual down manual sucks can someone help

__________________
04 Bonez LCD
egg II
14 pmi razzor barrel

soon 2 hav:
pmi 48/3000 n2 tank (aim me on pbnotoriousBAC if u sellin 1)
shocktech bolt

onesikpup

turn the manual down? wtf part of the gun is that?

__________________
FEEDBACK

SupahFly21

that must be cause of the paint you're using, depending on the bore size of the paint, the barrel will be more/less accurate.
you might be chopping because maybe you're egg had low batteries.how much did you chop? check the psi you're shooting at, make it under 400, and over like 200. the co2 wont be causing chops, but if you run on normal co2, i suggest getting an antisiphon kit for the co2. it should be like 10 bucks or something, check at a local shop, they might have it.
PE tanks with small gauges should fit, if you pull the ASA as far back as possible. but tanks like crossfires with the huge gauges will be very challenging to fit in.

i dont think you're bolt is the problem cause i have a shocktech supafly and it works fine.

__________________
-I dont Paintball anymore, but I enjoy watching, talking, and helping people with it.
"If you confess with your mouth that Jesus is Lord and believe in your heart that God raised Him from the dead, you will be saved." (Romans 10:9)

--I have a blue, small, CP Regulator (Spyder threads), that I want to give away because its the last paintball item I need to sell. You pay shipping plus 10 dollars and it's yours. PM me.