bunkertime

ok, Since sooo many people have been asking about if a Matrix bolt is hard to clean, I decided to make a little guide on how to Clean your matrix Bolt


Please Note i am using an Evolve Bolt Kit.


#1, Remove your barrel, Hopper, and tank, and remove the breech and backplate.



#2, Once you have removed your breech and backplate, For an evolve bolt kit, Use a 6mm Matrix Allen Key and remove the rear plug



#3, After remove-ing the rear plug, Carefully Remove the O-ring on the Tip of the bolt usuing eaither dental picks, or Tooth picks. Being careful NOT to scratch the bolt up



#4, Once you have the o-ring at the tip of the bolt removed, usuing your finger, PUSH the bolt assembly out of the back of the gun. DO NOT GRAB the Small end at the back of the gun, this can damage your bolt and you are gonna be mad Then wipe all the old greese off the bolt assembly

Please note i did not Remove the Front wall/beer can. This is because It does not need to be lubed as regularly as the Rest of the bolt assembly and is easier to cut o-rings on when replacing in the gun


**Note** At this stage, i personaly use Ardvark Customs Matrix Muck, But you may use any Matrix certified Lube you want to


#5, Now you can start Re-lubing your Bolt. Start by applying some lube to the SAIL on the bolt. This is the raised section near the front.



#6, Next, Put a small amout of lube inside the Top hat, then slide it onto the bolt and apply some lube on the o-rings ontop of it



#7, Now, Take the Black Tube/spacer, And slide it over the top hat. Apply a THIN layer of lube ontop of it to ease the process of putting it back into the gun



#8, Now, Take the Smaller spacer and slide it onto the bolt.

here is wut the spacer looks like


#9, Then, Take the Back wall, and slide it onto the bolt carefully, and lube the o-ring on it w/ some greese.



#10, Here is what your bolt assembly should look like so far

'

#11, Grab a drink of water... Your almost there

#12, Now CAREFULLY Slide the bolt assembly back into the gun, Making sure that the tip of the bolt goes through the beer can correctlyand without putting ne way,shape, or form of sideways pressure on the back of the bolt "tail"

#13, Now that you have the bolt assembly back it, Lube the "tail" of the bolt and the back plug and screw the back plug into the gun until it's snug.



#14, Replace the O-ring on the tip of the bolt


#15, Gas your matrix up and shoot 50-100 shots without the breech on to clear the bolt of ne lube that might have found its way in.

#16, Reassemble your Trix completely and Mow some major Muppets with a clean trix





Written and Assembled by Jared "bunkertime" K. Copyright 2004 bunkertime


--Kan Man

IM me if you have any questions at NorFlaBaller

__________________
she's a virgin if u don't count anal


•••

KingFikiElectra

Awsome. Rep 4 u

__________________
If you are for the resistance - SAY VIVA LA FIKI In your sig.
If you are armenian. Show it...
Don't You Wish You Were HYE?

No0bIe_PaIntBal

Not bad, not bad all.

Kyle_18

Hey *****SlapinWorr I e-mailed u but u not answering!

-KDAWG

__________________
907 ALASKA

Kyle_18

Are you here?

__________________
907 ALASKA

DemoCommando

nevermind. fixed it. When installing a new evolve bolt kit, remember to take out the beer can and front wall.

__________________
Demo Dan Paintball
http://stores.ebay.com/DemoDan-Pain...genameZl2QQtZkm

Authorized Dealer for Gen-X Global, Indian Creek Designs, Crossfire Air Systems,

I will have B2k5's and 05 Freestyles in stock soon again. Check for me on Ebay: Demo_dan

BALLER619

Why wouldn't you take out the beercan? Take out everything and make sure the o-rings aren't going bad, take all the old lube off and relube.

__________________
Island Breed

Feedback

bunkertime

Cause there is no need to relube the Beercan all the time. And When you take it out all the time, u are going to be replacing the o-rings on it alot more.

But.. if u wana take it out and relube all the time, Do so... i don't

__________________
she's a virgin if u don't count anal


•••

128shot

Nice fairy, i have never seen one that looked comfy with a 15* front untill now..good guide.

__________________
Some people are against capital punishment, because they say that it turns the state into a murderer. I'm against imprisonment, because it turns the state into a gay dungeon-master.

When I was a kid, I used to pray every night for a new bicycle. Then I realized that the Lord, in his wisdom, doesn't work that way. So I just stole one and asked him to forgive me.

PaintBallBob

when putting the bolt assembly back in, do you put it in the front(back plug first) or put it in the back(bolt first)?

__________________
Gloss Black DM5 F/S/T

BALLER619

Put in the front spacer and beercan in first, then put the main spacer and tophot on the bolt and put that in, and have the bolt sticking out some so you can continue to put parts in as they're lubed, then the rest as you continue to lube parts.

Don't neglect your parts, take out everything and relube everything, I've had 3 matrices and I've only had to replace maybe 3 o-rings tops when I recieved the guns.

__________________
Island Breed

Feedback

rivit

how often should you clean the bolt?

__________________
TOXIC TRIX OWNER

rivit

bunkertime

I cleaned my bolt after every day of play.

__________________
she's a virgin if u don't count anal


•••

silverbara

Im sorry this has nothing to do with relubing, but which version of the SCM is pictured on the gun in the first pic? SCM, or SCM2? Thanks.

bunkertime

Scm 1

__________________
she's a virgin if u don't count anal


•••