NorCalBaller

ok so i don't know if this is a problem with my gun or the cp reg i bought, but my gun refuses to shoot over 256 fps. sometimes i can get it to shoot at 270and be pretty consistant but the next time i chrono it's right back down to 240-250 and i tried turning the velocity up. i went all the way up to 400 psi and it was still shooting 250.. what do i do?

NorCalBaller

could it be my shocktech bolt that's doing this?

bobide

you need to rebalance your regulators. Hpr to 220psi then turn lpr till bolt cocks back keep turning till noid leaks. Turn lpr back 1/4 turn. Now chrono. Adjust hpr for velocity.

Lemme know how that goes.

__________________
05 PROMASTER , 14" Macdev Matchstick, Kila Drive, Zentriam Valve, ICDU ram, CCM no-rise, Sonic lpr

NorCalBaller

how do i adjust the lpr?? i know that's a noob question bu tim just getting used to electro pneumatic guns..

bobide

the regulator below the barrel. Use a coin to turn it. To the right increases pressure.

__________________
05 PROMASTER , 14" Macdev Matchstick, Kila Drive, Zentriam Valve, ICDU ram, CCM no-rise, Sonic lpr

NorCalBaller

hmm.. you'd think turning it to the right would decrease it.. oh well.. i would have asked the people at the field i play at but i don't think they would know, or even give a ****.. so thank you very much for your time.

drumbum19

Switch out the batteries. I know it sounds too simple. But, this happened to me once, i just had to swap that batteries and then it worked fine.

__________________
- Watch yo self

"For Motha Russia"

Custom Pro with Response Trig, HP Reg, CP Barrel, m16 body kit, and car stock.

Promaster w/ CP on/off ASA, CP Shorty HP Reg, J&J S2 Barrel, and Dye Stickys.

icdpromaster7

Hey guys, i know that tis isnt my post, but I just bought a Promaster, and i dont know how to change the velocity. If you guys could help out, that would be great.

NorCalBaller

it explains how to do it in the manual that the promaster comes with, it's quite simple actually, and it's the same for basically ALL high end paintball guns, on the regulater or as it is also known as the front fore grip, there is a screw, turn it to the right, your velocity goes down, turn it to the left, your velocity goes up,

a little piece of advice, less is better, start with a low psi, then work your way up to the right velocity, i ended up bending a valve because i accidentally turned my psi up too high,

__________________



Red Promaster

Upgrades - Ndz on/off asa, Virtue destrokyr .45 grips, Kila Drive Board V2.2, Kila Magnetic Detents/Eye Covers, Vaporworks Laser Eyes, CP reg, DBN 15 Degree ASA adapter, CP Trigger, Crammer 2.0(Ram housing and shaft - only 40 made), Ebay Valve, AKA SCM III Low Pressure Regulator, BP Bullet Nose Adjuster cap for SCM III, Shocktech Superfly Bolt Pin, Deadlywind Carbun Fibur Barrel w/ Deadlywind Insert Kit, Low-rise clamping feedneck from ebay (no brand name).

Setup - Red Promaster, Vlocity Jr w/Gangstar chip, PMI 45ci/4500psi w/NXe black cover

icdpromaster7

Thanks, but one last thing. U guys may have ahd this problem, but when i attach my hpa tank, i can tell that the air goes through the macro line, and the regulator reads that there is pressure, but when i tun it on, the bolt doesnt go back, and it doesnt shoot. So i was advised to try switching the battery, so i did that and nothin happened. Just curious f im not doin something or if someone else has ahd this happen to them.

TheAznInvazn

Your LPR, re-adjust it

__________________

icdpromaster7

thanks il try it out, but i dont have any air right now :P