NorCalBaller

ok soooo i have finished putting just about everything i could ever want onto my promaster, and i want an lcd on it


i realize this is going to be difficult but i want to try, i just want to know what board this would be easiest with

__________________



Red Promaster

Upgrades - Ndz on/off asa, Virtue destrokyr .45 grips, Kila Drive Board V2.2, Kila Magnetic Detents/Eye Covers, Vaporworks Laser Eyes, CP reg, DBN 15 Degree ASA adapter, CP Trigger, Crammer 2.0(Ram housing and shaft - only 40 made), Ebay Valve, AKA SCM III Low Pressure Regulator, BP Bullet Nose Adjuster cap for SCM III, Shocktech Superfly Bolt Pin, Deadlywind Carbun Fibur Barrel w/ Deadlywind Insert Kit, Low-rise clamping feedneck from ebay (no brand name).

Setup - Red Promaster, Vlocity Jr w/Gangstar chip, PMI 45ci/4500psi w/NXe black cover

martix_agent

errr, uhhh..

there's the old bushmasker 2000 boards but i dont' think that's what you want.

I know that ego boards work with the solenoid, maybe use that? I also hear that cyborg boards do as well.

__________________

If your a Christian paintballer put this in your sig.

Another promaster for sale $100!

bobide

A blast tech modded in a timmy board and the lcd off it if I remember correctly.

__________________
05 PROMASTER , 14" Macdev Matchstick, Kila Drive, Zentriam Valve, ICDU ram, CCM no-rise, Sonic lpr

NorCalBaller

bobide, if you could get a picture of that, that would be awesome..

i realize this is going to be hard but i really want it, how kick ass would it be, plus if i do a good job i think i could bumb up the resale on this puppy

i'm looking for a board that uses the most of the same plugs for like the eyes and battery and all that stuff

__________________



Red Promaster

Upgrades - Ndz on/off asa, Virtue destrokyr .45 grips, Kila Drive Board V2.2, Kila Magnetic Detents/Eye Covers, Vaporworks Laser Eyes, CP reg, DBN 15 Degree ASA adapter, CP Trigger, Crammer 2.0(Ram housing and shaft - only 40 made), Ebay Valve, AKA SCM III Low Pressure Regulator, BP Bullet Nose Adjuster cap for SCM III, Shocktech Superfly Bolt Pin, Deadlywind Carbun Fibur Barrel w/ Deadlywind Insert Kit, Low-rise clamping feedneck from ebay (no brand name).

Setup - Red Promaster, Vlocity Jr w/Gangstar chip, PMI 45ci/4500psi w/NXe black cover

bobide

Don't think I have the photo. I believe he used a frenzy board off a 2k2 timmy. Had the membrane pad right next to the grips. You won't have any luck with your plans for the harness plugs. You will need to splice the promaster's harness to the timmy board. It isn't as hard as you think.

__________________
05 PROMASTER , 14" Macdev Matchstick, Kila Drive, Zentriam Valve, ICDU ram, CCM no-rise, Sonic lpr

NorCalBaller

yea i think i might as well buy a new harness from paintballtrader.com cause i think the wire going to my eye is crimped, but i'll look at the timmy boards, thanks for the help

__________________



Red Promaster

Upgrades - Ndz on/off asa, Virtue destrokyr .45 grips, Kila Drive Board V2.2, Kila Magnetic Detents/Eye Covers, Vaporworks Laser Eyes, CP reg, DBN 15 Degree ASA adapter, CP Trigger, Crammer 2.0(Ram housing and shaft - only 40 made), Ebay Valve, AKA SCM III Low Pressure Regulator, BP Bullet Nose Adjuster cap for SCM III, Shocktech Superfly Bolt Pin, Deadlywind Carbun Fibur Barrel w/ Deadlywind Insert Kit, Low-rise clamping feedneck from ebay (no brand name).

Setup - Red Promaster, Vlocity Jr w/Gangstar chip, PMI 45ci/4500psi w/NXe black cover