bennieboy2290

ive recently got my bushy and when got out to shoot, sometimes it wont shoot (I have PDS) so i took off my hopper and droped a ball in one at a time to see why the PDS wont detect the ball. It looks like sometimes the ball gets rolled back against the bolt or foward and its not in the middle so PDS doesnt see it.

My batteries are fine and i dont have small paint (its severe hurricane .689 paint) What do you think?

__________________
ICD owner #32



Black to blue B2K4 PDS | Black to blue Check It unimount | 68/45 high pressure Crossfire HPA tank

c'mon, it sounded funny... i had to

No0bIe_PaIntBal

Umm, I think I have heard of this problem before. First of all, I would clean your eyes to make sure your eyes aren't dirty.

bennieboy2290

i have already done that, i know that the eyes work, its just the ball isnt where its supposed to be

__________________
ICD owner #32



Black to blue B2K4 PDS | Black to blue Check It unimount | 68/45 high pressure Crossfire HPA tank

c'mon, it sounded funny... i had to

sNoW PIrAnHa

New detents? you could just turn off the PDS.

__________________
"I have no mercy or compassion in me for a society that will crush people, and then penalize them for not being able to stand up to the weight"- Malcom X

bennieboy2290

yea ive tried that, but ive just been shooting around the house and when i get a ball break... man its a pain to clean, it gets all in the eyes and junk, and the detents are fine cause the ball doesnt roll fowards, just backwards in the chamber

__________________
ICD owner #32



Black to blue B2K4 PDS | Black to blue Check It unimount | 68/45 high pressure Crossfire HPA tank

c'mon, it sounded funny... i had to

BushmasterMAN

If there's a way to adjust where the bolt is then try that.

Carmas

Uh did you try aiming your gun at a downward angle and seeing if the PDS detects then?

__________________
Armenian kid.

titocampos1990

jeez, im always hearin of icd's wit defectiv problems like this.

bennieboy2290

well ive got it to work, i can shoot a string of paintballs and when it stops, i just have to tilt the gun to a different direction and give it a shake, then it will shoot some more i just have to do this every 30 balls or so. I just thought that it shouldnt be having these problems for the 500$ that i spent on it... but o well

__________________
ICD owner #32



Black to blue B2K4 PDS | Black to blue Check It unimount | 68/45 high pressure Crossfire HPA tank

c'mon, it sounded funny... i had to

titocampos1990

that would bother me

ChaosTheory

if its rolling forward get new detents. if the you look down the feedneck and the bolt look like its too far back you can do the ram mod. just stick an oring in between the part of the ram that moves. it will make the bolt not go back so far. you do want a little gap though so the ball has time to drop all the way down.

__________________

BushmasterMAN

Thats what I wanted to say, Thats what happened to my tintimidator when I first used it.Two balls were getting into the chamber when I would stop shooting so when I would soot again it would shoot two at a time sometimes.We just adjusted the ram and then it worked fine.So like chaos said put an oring or anything else in there that won't hurt the gun but it will keep the bolt from going too far back.

elementboarder5

Do the ram bumper mod. Search pbn for it. It was happening with my gun (balls rolling back in the breach, causing double feeds with small paint) And i did it, i put an orthodontic rubber band behind the hammer. works great.

__________________
Feedback
Electric blue vision shocker f/s/t
Louis Vitton halo shells, retro straps, shocker pipe kit
Hot Proto F/S/T

ChaosTheory

i did the mod because why my bolt pin went back it was denting my gun. so my it caused the metal to drop down and my bolt was getting scraped. i sent it to icd to fix and it was still where it could hit so i just did the mod.

__________________