p8ntballfan1

Which in your peoples opinions would shoot faster?....

Gun A- Spyder TL with an E-grip on it. 12 inch barrel, lp chamber and such u know whats all on the gun, but just add an e-grip.

Gun B- Spyder imagine with e-grip , 12 inch barrel also, same things as the Spyder TL as far as everything on it, the only difference is the bolt isnt moving outside the gun on this imagine, so...

Which do u guys think would shoot faster? or about the same? and how fast do u think u could get?

__________________
GodSpeed.....

HuNtS

they all shoot the same man, all spyders are capped at 12 or 13 bps.....

__________________

Joshh100

if you add a t-board.. then you can shoot 36 bps if your fingers could ever move that fast. If you are interested in shooting real fast, you can get a t-board for 60-70 bucks.

p8ntballfan1

na i dont need a T Board and i guess now my only problem is gettin that Spyder TL with e grip to stop leakin air....

Keep them opinions comingg.....

__________________
GodSpeed.....

BC_paintballa

well, I might be able to help you with your leak.

p8ntballfan1

yea, i need the help heres the problem:
Air leaks from inside the barrel which has something to do with the valve stem assembly....
1. the Cup seal and valve stem assembly is fine, theres nothing wrong with it, ive checked it and replaced it, still leaking.
2. THe bolts are all lubricated, and the o-rings on them are fine.
3. im guessin it has something to do with the bolt/striker pushin in on the valve stem just a little which is allowin air to travel up through the hole and out the bolt and down the barrel.
Tell me what u think is wrong and what u think i should do to fix it.....

__________________
GodSpeed.....

BC_paintballa

well, that sorta thing happened to me a few times. I think what is, is it has something to do with low co2. cauuse when I was running low on co2, my marker un cocker and started leaking out co2 in the same place as you said. So fill up your tank and then try it, casue that worked for me. If that fails then take it up to your feild, and see if they can fix it.

pimpin balla

screw in your co2 then cock it if it starts to leak, mine does that sometimes and it always stops when i cock it tho.

lovetocheat69

Try 40-50 bps.

__________________

p8ntballfan1

ha yeah i noticed today when i hooked up the air, i was running really low on Co2 and im sure that is the problem. and im going to try again but with a full tank, thanks dudes , PEacE~

__________________
GodSpeed.....

HuNtS

OMG it MUST be because of the new milling!!!

__________________

BC_paintballa

Also remeber to cock your gun before you air it up.

paintballjunk12

y

BC_paintballa

because if you dont air will leak out of the barrel. I dont feel like going into detail, so I wont.

p8ntballfan1

but ive been playin for like 2 years and have always hooked up the air source before cockin the gun but i guess ill try that cocking thing first then

__________________
GodSpeed.....

KingFikiElectra

If you ave a lighter valve spring then the striker, when idle will be making contanct with the pin so air can escape. If its stock you should be fine.

They also shoot roughly around 13-14bps. Thats what the stock board is capped at.

__________________
If you are for the resistance - SAY VIVA LA FIKI In your sig.
If you are armenian. Show it...
Don't You Wish You Were HYE?

p8ntballfan1

yeah well im sure thats the problem and yes the valve stem assembly and such is all stock. And yeah it is capped at like 14 bps, too bad it isnt faster but its aight, its not how fast , its the accuracy but how fast it shoots helps. thanks dudes, peace~

__________________
GodSpeed.....

lovetocheat69

What are you talking about. I hope you know I'm right.

__________________