lostpaintbalman

undefinedundefinedundefined
I'm new at handeling ths paintball gun ,th SPYDER IMAGINE. and i took off the cocking bolt and spring and i don't know how to put it back on?? if anyone knows please e-mail me at Heavymetalmaggot@aol.com it is an emergency and please. or if u know of a website that tells you how to put it back together give me the site please. Thank you

lostpaintbalman

i'm a loser

dirtrider

If you have the manual, check it. There should be blow up diagrams. Also, there is a blow up diagram/schematics right here. If the link doesnt work just go to www.kingman.com and go to tech support then click on your gun's diagram. EDIT: And yes, I agree, you are a loser.

__________________
$LCD Matrix$- like new, tons of ups!

t33kyboy

Theres also videos on how to disassemble a spyder in the Media section on Kingman.com

__________________

DJS2

if u take a picture of the parts i can number the picture and tell u what to put in first and where.

KrAzAyInSaNe

Whatever you do, dont try to figure it out.

__________________
Smartparts Owner 65

lbreevesii

OOOOOOO!!!! i know!!!! go to the forum entitled "stacked tube blowbacks(spyder clones)". then click on the link for kingman/spyder. then, ask there. actaually, it'll probably get moved anyway. heres the way it goes. hammer(metal can sort of thing). it is attached by a metal pin to the top bolt. after you slip these two bolt into the gun, you then put the main spring and urathane dampaner ring back into the gun behind the hammer(lower tube). next you replace the small rod that is/was inside of the spring. next you slide the endcap back on, and push the retaining pin back through its hole in the gun. wow, wasn't that hard.

__________________
member of the COG, TOG, ICDOG, SPOG, IONOG, member #'s 25, 80, 19, 7, and 7.
Founder/Prez of PBA

VIVA LA FIKI!!

bobide

on kingmans site there are also videos that would really help u out.

Ok, if everything came out you should have these peices.
-bolt
-spring
-shim (bout 2 in long, should be black, has a flat circular edge)
-back block part
-little silver disk
-bumber (black has a hole in it)
-striker (came out of bottom tube, connects to bolt)
-and quick strip pin

get the bolt and attach it to the striker. Then guide those 2 parts into the gun. Next put the bumper in behind the striker (bottom tube) Turn on ur gun and pull the trigger (while doing this put some pressure on the bolt, this will allow the striker to move forward over the sear which is holding it back) slide the bumper in as far as possible. Next put the spring in the bottom tube, it should go through the bumper, next put the shim through the spring, finally take the silver disk and put this on the bottom part of the end cap. Attach end cap, put quickstrip pin back. And ur good to go.

__________________
05 PROMASTER , 14" Macdev Matchstick, Kila Drive, Zentriam Valve, ICDU ram, CCM no-rise, Sonic lpr

sNoW PIrAnHa

make sure to throw away all the plastic and rubber parts. And be sure to put oil (vegetable oil works best) on the flux capacitor.

__________________
"I have no mercy or compassion in me for a society that will crush people, and then penalize them for not being able to stand up to the weight"- Malcom X

KingFikiElectra

hAHAHAHA R00FLESKAT3S!!!!!!!111111ONEONE1

__________________
If you are for the resistance - SAY VIVA LA FIKI In your sig.
If you are armenian. Show it...
Don't You Wish You Were HYE?

dirtrider

yeah hes retarded but hes new. take it easy on him...

__________________
$LCD Matrix$- like new, tons of ups!

pballman31

Ever heard of an owners manual?

[^_^x]

damn spyder imagines are so damn complicated.

__________________


Dragun "The One"
Black/Green Fade
Dye Excel Barrel 14"
Halo B w/ Rip Drive
1337 Remote Control Setup (Limited Time only).....

32 Degrees Rebel 02 Electronic Vertical
Black
Dragun Stock Barrel 12"
Gravity Fed Hopper

n00b Gun Package Under $90

spyshark

Haha that's a funny one man considering some of your questions,LOL.

__________________

visionimpulse2k

u really like to bash on people dont u..always bringing up others posts..hmm...

anyways..watch the video at kingman.com ....it will help a lot

__________________
Team S.N.A.F.U
*sponsered by paintball daves*

DM3

big_balla

As everybody before me posted, go to the Kingman sight, and there is a video. Download it, and watch it, it's very simple. I think it's something like "Basic teardown" or something. Spyders are one of the easiest guns to maintain, once you get the hang of it.

__________________

spyshark

[quote=visionimpulse2k]u really like to bash on people dont u..always bringing up others posts..hmm...

Just keeping it real man.

__________________

pballman31

^If I remember correctly,none of my questioons were answered in the owners manual.

spyshark

My apologies,the only dumb question is one not asked.Bad hair day,LOL

__________________

Born2drive

i remember taking my old imagine apart, not knowing that you had to put the bolt and striker in as on piece and then frantically trying to put it back before my mom came home and yelled at me. (sighs)