Thread Tools

**txaggie08** · February 9th, 12:41 PM

OK, take the front cap off the gun, and the spring/cup seal/valve stem will come out. The cup seal is the white piece sitting against the valve.

I can help you wiht this alot easier if you will get the gun in front of you and catch me on aim sometime...

ShinryuBaller · February 9th, 02:00 PM

I first started out with one of these 4 years ago.
I always had problems with it and ultimately ditched it to a friend for a dye invision mask.
He sells me so much paintball stuff for cheap its not even funny XD
for the r6, i recommend keeping the cupseal very clean and make sure you NEVER scratch it. Mine always ****ed up, so i recommend upgrading to at least a spyder, but you don't have too, thats just my opinion.

steve22 · February 9th, 04:33 PM

is the white piece sining in side of the gun if soo it dont look like it wants to come out

***TheAznInvazn*** · February 9th, 06:13 PM

It shouldn't be hard to get out. It should just slide right out with the Vertical Adaptor.

steve22 · February 10th, 08:49 AM

one thing slid right out it was a spring than a spacer that looked like an x than a metal pole about 1 inch long with a red nipple like thing on the end than when i look in there is a white ring sitting in side

***TheAznInvazn*** · February 10th, 11:40 AM

pics?

Still not sure about what you're talking about.

**txaggie08** · February 10th, 12:22 PM

What came out was the cupseal. The white ring inside was the valve. Theres a set screw under the frame , then you push it out.

steve22 · February 11th, 07:22 AM

yep i found the screw to un tighten now i can slide it around but when trying to get it out the frount of the gun there is a small nik from the hose that connects to it from the botom.
ill post some pics
thanks for the help

steve22 · February 12th, 04:51 PM

alright i managed to get the cup seal out and replaced the orings but. i was looking around and i noticed that the cocking system the botom bolt that goes into the gun that oring is damaged and it is a different size and color im not sure were i can get those but going to look at sports athority tonight
i did hook up the tank and it was leaking like it was befor so i will try the different looking oring

**txaggie08** · February 12th, 09:55 PM

That's the striker o-ring, and a tank ring will usually work there as well in a pinch. That's not what's leaking though(it does need to be replaced obviously or the gun will not recock)

You replaced the cup seal and both o-rings on the valve body itself right?

steve22 · February 13th, 03:40 PM

yep i replaced the cup seal and i need to get some o rings to replace the two on the valve. you know which way goes in first? does it matter?

***TheAznInvazn*** · February 13th, 07:41 PM

Yes it does, I believe the side with the bogger hole faces the front of the marker

**txaggie08** · February 13th, 10:02 PM

bigger hole definitely has to go facing the cup seal.

steve22 · February 14th, 03:41 PM

replaced the rings and put it all back together and the pissing sound is less but still there but it wont be their than i take a few shots and its back
any suggestions

**txaggie08** · February 14th, 04:03 PM

hmmm......can you tell EXACTLY where it's coming from(ie down the barrel or just around the valve.

***TheAznInvazn*** · February 14th, 09:55 PM

Damaged valve might be on the worst case scenario side...

steve22 · February 15th, 03:34 PM

it is comming from where the hopper goes on and you can also here it coming from down the barrel

steve22 · February 18th, 08:28 AM

should i replace the valve in it?

steve22 · February 19th, 09:35 AM

if you say i should replace the valve i found a good deal on a high flow valve would this be good in the gun?

***TheAznInvazn*** · February 19th, 11:19 AM

A highflow valve will get you better efficiency, and possibly better consistancy.

It might be worth it to just buy one and see what happens