[S.O.T.A]

i had a paintball explode in the chamber where the bolt hits the ball and now the bolt will not move. and there is a broken paintball stuck there. help me.

[xxxfirexxx]

Good god, how in the hell did that happen, what type marker you use? Id reccomend taking the marker apart as well as you can. *taking out the bolt* then scrubbin the insides with a squeegee, then scrub the bolt with a rag because that paint is kinda oily. Then get all shell fragments out by using a squeegee and a vaccuum/air compressor. Then after that, lube ur gun up, lube up the parts, and put it back to gether. it should work.

[S.O.T.A]

i use a custom diablo gun. i was just shooting it in the back yard testing it out. cause i just got it. and then it just happened. I can see the shell fragments jammed inbetween the bolt and body of the gun. And my tools are packed up because we are remodeling is there any way i can get the shell framents out without taking the gun apart?

[xxxfirexxx]

not that I know of. Hmmmmmm, you may want to consult diablo and ask them though. Your dad have a truck with a toolbox in it? if so get the necessary toolsu need and get to work as best as u can.

[MotorCity Hertz]

take the barrel off if you can and hopper.... reach your finger inside and take out all fragments.... i dont think its fragments that is blocking the bolt it could be a jammed paintball...

[S.O.T.A]

i got the fragments out and i have shot it but it will only shoot once. then i have to pull the bolt back to shoot it again. there is paint on the bolt could that be the problem?

[Smitty]

Dude what you've got there is a seriously chopped paintball. Ive only seen that happen twice. Use tweezers.

[ZeRO eFFeCT]

Im pretty sure you can remove the bolt without having to take it apart...Just get the bolt out, wipe it off, then wipe the insides...

How fast were you shooting and what paint. You can only go so fast with guns like that and normal hoppers.

[Zeotranatix]

lol yea that happened to me and my bushy when i 4got to turn my hopper on ....

use a screwdriver and get ALL the fragments out

use a straight stick to push the bolt out clean everything put it together and it should work

zeo

[¤COLD¤]

kncok the bolt out by takig off barrel bit screw driver on end of bolt and hitting it backwards

[S.O.T.A]

i was shooting pretty fast and the hopper isnt electric. I got the gun fixed a few minutes ago going to play woodsball tomarrow.

[Javaman]

It happens pretty rarely but when it does take out the retaining pin (which holds in the hammer and bolt) All it takes is strength if the shell is wedged in there tight. Be careful though since the back plug is already under spring tension. If it were to give-way while putting a lot of back pressure on the bolt it would likely shoot across the room or field taking with it your striker buffer, spring guide and spring. If you still can't get it to budge remove your hopper and stand the gun upside down in water (hot preferably) so that the bolt tube is completely submerged. After several minutes the gelatin will soften enough to get the bolt out.

[NYY]

just dont be afraid to take apart your gun. Get the bolt out and clean it, and clean the body as well

[Bane]

You should actually practice taking apart your gun and putting it back together, just so you get more comfortable with the idea. Plus, if you need to clean it while you're at the field, you'll be able to do it faster

[sNoW PIrAnHa]

Take off the quick disconnect watch out for the bottom tube itll spring out at you. Try to remove the bolt then clean everything. Then get as much stuff out as you can by using tweezers and such. Then if its still stuck then get something like a drumstick and put it in the barrel then get a mallet and hit the drumstick, the force will usually knock the bolt out from its stuck position. This happened to me on my spyder xtra, if you need any more help then just pm me.

[Javaman]

Drumstick? Wouldn't you get a bunch of chicken grease in the gun? j/k. I always wanted to take a band photo with me holding chicken drumsticks instead of wood ones.

Javaman, (ex-drummer)

[elementboarder5]

also, if u have the recocking problem... just lube your bolt if nothing else seems to be working

[TerminAZN]

MY TRICK HAPPENED BEFORE HERE:
step 1: get a hammer
step 2: plyers
Step 3: turn plyers upside down and use one of the legs
step 3: stick in champer
step 4:AND START UR GHALLEGER IMMPRESSION!!