Thread Tools

**MuddinPede_98C** · October 2nd, 07:46 PM

Bad day for the Imp. Well, I just put in WAS, and was ready to lay some ropes down. It had other plans.

Well, I fill my tank and put the halo on, thew a quick line of balls to make sure everything was working, and it was. Well during the ten second countdown, I still had my doubts, it being new and all. So off the break I shot like almighty hell, then I get a chop, then about 2 more good shots I get about 15 chops in a row. I get to my bunker and squeegee, thinkin they were bustin in the barrel. I come out the right side and start layin it down. Out of 25 or so shots, 2 balls actually leave my barrel. So after that, I decided it wasn't gonna work.

After the game, I take the bolt out and clean everything. I shoot a few without the barrel, and had all chops. None of them were because of double feeding. I'm almost positive when I put in WAS, the hole you cut for the eye couldn't be any smoother. Sharpied the raw metal and everything. So I take my eye out to clean it, and after I do, it still isn't acting right. It would shoot whether it read something or not. I look at the board and there is no paint on it at all. Changed batteries, reset board, still no luck. As of right now it still is messed up.

I tried both eye modes, no luck. Tried turning dwell down, no luck.

Here's my setup if it helps:

...Nasty Impulse
WAS
CCM No-Rise
Halo B
White delrin bolt
Brass hammer
Ti pull pin
SS ramshaft
Tapeworm
Vert maxxy
SP non-vision ball detents
PE 68/4500

I'm just kinda pissed off I have a nice Imp, and had to use my Tippy all day.

Any help is very greatly appreciated.

**D FO** · October 2nd, 08:22 PM

i dont know to much bout was but if you can try and turn the eye off.did you drill the whole for the eyse yourself? take it to an airsmith/proshop

**MuddinPede_98C** · October 2nd, 08:27 PM

Tried turning the eye off, still didn't work. I'd like to fix it myself insted of taking it to my local pb store. The owner is a dickhead and hates SP guns, so he'll half-ass it like he does everything else.

**D FO** · October 2nd, 08:58 PM

check your bolt to see if theres any sharp edges on it i doubt it because it started happening right when you got was. hmm theres probaby a sharp edge were you put the eye in. does it chop when you shoot like one ball at a time? now that i think of it it might be your dwell or maxflow.

**MuddinPede_98C** · October 2nd, 09:16 PM

Adjusted dwell and max-flo. Chamber and bolt feel smooth.

**D FO** · October 2nd, 09:20 PM

did you get anything else with the was like a new hammer or ram assembley or anything or a new bolt pin?

**D FO** · October 2nd, 09:26 PM

also did you put the shims of the ball detent on the new WAS eye? i have a feeling this is it

sorry for double post

**MuddinPede_98C** · October 2nd, 09:38 PM

Bought WAS only. How many shims and on wht sides should I try. I was kinda thinking shims, but put it off.

**D FO** · October 2nd, 09:39 PM

u put the shims on the detent on the WAS side to that it lines up right . im thinkin this is it im readin the manual real quick

**MuddinPede_98C** · October 3rd, 07:52 PM

What do you mean "so that it lines up right"?

**crazycupcake** · October 3rd, 08:10 PM

did you try different paint? might work 0?

**MuddinPede_98C** · October 3rd, 08:13 PM

Tried Heat, Gameface, and Marballizers. All chopped like a mofo. So how many shims and on what side is it supposed to be.

**bunkertime** · October 3rd, 08:20 PM

I believe ur supposed to put like 5-6 shims under the Vision side detent when u install was so the detent doesn't poke through too much

**MuddinPede_98C** · October 3rd, 08:44 PM

It says to put them on if you use vision detents. Mine are non-vision. I'll try it tommorow anyway.

Thread Tools

View more Paintball photos