Fantasyfire

Alright, on my Imp I have a Blade Magnetic trigger, and the thing will not respond to my gun or something. It feels like it's too tight. After I took out the grip frame screws and then put them back in my trigger wouldn't work.

The light in the back will usually light up as you hit your trigger (vison turned off), and it doesn't light up when I pull the trigger.

*This is not a newly installed trigger, I have been using it for a while*

This same thing happened to me last weekend on the field, so I took it to the matience guy and he took a very small allen wrench and stuch it up my trigger, and did some twinkling. Then it worked. I didn't think to ask him what he had done, or how to do it.

Any suggestions to help?

__________________


2003 Black Smart Parts Impulse w/ Vision

Ups - New Designz Equalizer Bolt, Chrome Drop Forward, Clear Dye Stickies, Silver Blade Magnetic Trigger, Silver Twister Feed

Gear - Smart Parts 14" Freak Barrel System, Rikochet Apache Hopper

Darkpaintball

My guess is that the trigger isnt activating the microswitch. What u need to do is take a small allen wrench, not sure the size, and adjust the first screw on the top of the trigger.

__________________

FEEDBACK

Huey69

On my shocker when that happens it either means my Trigger activation switch is in too far or not in enough. I'm not sure if an imp trigger has that type of screw, but if it does adjust it. Whats most likely happening is your screw is moving.

__________________
Taking a break....teamless for now

Uncle_T

yeah your not activivating the micro switch get a .05" (i think thats the size) allen wrench and adjust the screws in the trigger

__________________

bunkertime

this is wut i always sugest to people,

Unscrew it all the way, then turn the gun on and screw it in slowly until it clicks and u should be done quick and simple.

__________________
she's a virgin if u don't count anal


•••

MuddinPede_98C

Mine moved around, too. I just put a little teflon tape on the screw.

__________________
Corey Nichols

Orange to Black Alias Timmy | Infamous Board | Dye Ultralight | CP Roller Trigger | Black Unimount | Halo B | Pure Energy 68/4500

Fantasyfire

Alright I tried twisting the screw up higher to hit the switch but after a little bit of twisting the screw, my trigger gets so tight, and the light was still not flashing for each pull.

Whats the deal?

__________________


2003 Black Smart Parts Impulse w/ Vision

Ups - New Designz Equalizer Bolt, Chrome Drop Forward, Clear Dye Stickies, Silver Blade Magnetic Trigger, Silver Twister Feed

Gear - Smart Parts 14" Freak Barrel System, Rikochet Apache Hopper

xPiZZeRx

When you're not pulling the trigger, is the light in the back blinking twice every couple second?

If it isn't, that means you need to back down the switch activation screw a little, so that it does.

Is there another screw on the top of the trigger, but closer to the front end of it?

If so, loosen that screw a little so that the trigger isn't as tight, and it adds some side to side play.

__________________

Fantasyfire

Yea the light does blinking, just not with the trigger pull.

There's another hole in the front end of the trigger, not sure if there's a screw up there but I'll try it.

__________________


2003 Black Smart Parts Impulse w/ Vision

Ups - New Designz Equalizer Bolt, Chrome Drop Forward, Clear Dye Stickies, Silver Blade Magnetic Trigger, Silver Twister Feed

Gear - Smart Parts 14" Freak Barrel System, Rikochet Apache Hopper

xPiZZeRx

If it's not blinking when you'r not pulling the trigger, then tighten the switch activation screw until you hear a click. After that, the imp should not be blinking if you're not pulling the trigger or holding it in. this is because the switch is activated. After that, loosen that screw just a little bit so that it starts blinking again. Then tighten the screw that is in the middle of the trigger. The one that determines how far of a pull you will have. Adjust that until it is pretty short, but still not too short so that the switch is always activated.

get it? lol.

__________________

ggollek

i bougth a mag trig and my friend did we both had the same prob u have to take the board tray off and stick a allen through the top and back out the screw the screw goes down to far and isnt alowed to rise enogh

xPiZZeRx

That's the magnet that you are adjusting. It's basically the sensitivity of the trigger. Back it out as far as you can. Personally, I put it so that the top of the magnet is flush with the top of the trigger frame, it's pretty sensitive.

All other screws/adjustments are external.

__________________

MuddinPede_98C

My magnet is external. I use an Eclipse Blade trigger.

__________________
Corey Nichols

Orange to Black Alias Timmy | Infamous Board | Dye Ultralight | CP Roller Trigger | Black Unimount | Halo B | Pure Energy 68/4500

xPiZZeRx

The magnet can be an external adjustment, but that's only if you put it under the trigger, so it attracts the trigger, if on top, like his and mine, then it repels the trigger, which I think is better.

__________________