Thread Tools

titocampos1990 · August 2nd, 08:28 PM

1. do i need a low pressure tank for an angel?

2. the 2 holes under the barrel, what are they and what should i buy to put in them?

3. if i send an angel to theangelguy.com they will put eyes and a was board correct?

themainevent · August 2nd, 08:34 PM

yea, i think you need a lp tank with the speed, not exactly positive on that, the holes I know you can put like volumizers in them, and i dont know if theangelguy has WAS/ACE but i do know he can put in a predator board with ACE

**BunkerMonkey** · August 2nd, 09:34 PM

TAG does his own predator board and eyes IMO better than WAS.

and I AM positive you need a low pressure output tank unless you wanna do the minireg mod.

titocampos1990 · August 3rd, 04:41 AM

4.can you adjust debounce on a speed?, because i know the speed is a simplified angel.

5.if it has a predator2 board, can you still adjust settings on the back of the handle or do you have to open the grips and change it on the board itself?

6. the 2 holes under the barrel... wich one is wich and does an lpr come with the gun, and if not, do i need to buy one to make it work?

7. what is the optimum pressure and dwell i should set on a speed to get maximum performance?

**SunTzu** · August 3rd, 10:56 AM

4. no cant adjust debounce or bounce on a speed with the board that is anyways

5.i think the pred board you set settings with the trigger (dont know for sure)

6.hold the gun with barrel pointing away from you right hole exhaust valve ( this is also where the volumizer would go), left hole LPR,... take gun out box, fix tank and rip

7.tank output 450psi, from minireg into gun 200-250 psi
LPR @ 55psi, dwell 16-17 ms these settings are from angel-owners and work great on my speed, with the medium volumizer

titocampos1990 · August 3rd, 11:39 AM

do the volumizors come with the gun? and what lpr do you recomend

**SunTzu** · August 3rd, 11:44 AM

some companies offer packages with volies in them but normally they dont come with the gun and the LPR is already there no need to buy one

titocampos1990 · August 3rd, 04:08 PM

how do i know what the lpr is set to? is there a gaugeor do i have to buy one.

**SunTzu** · August 3rd, 04:17 PM

angel toolkit all you need to buy for maintaining your angel
it has a gauge to check LPR, ram adjuster and a LPR removal tool

titocampos1990 · August 3rd, 04:22 PM

Laaaaast question...(cuz i know im pissing you guys off) why would i need to adjust the ram? and i know what a ram is in a cocker but i have no clue what a ram is on an angel.

**SunTzu** · August 3rd, 04:44 PM

the ram operates the hammer, which operates the bolt and the opening of the valve, every time you pull the trigger the ram pushes forward the hammer, this takes the bolt with it, the hammer strikes open the valve and puts the bolt over the valve and a paintball is fired in some direction.
the bolt pin slots in too the hammer but there is no perfect fit, the position of the bolt pin on the hammer influences the distance of the bolt in the breech (when fired), you have to align the ram which also adjusts the hammer so every time you fire, the bolt is in the correct position at the end of the cycle.
if not it could cause the bolt to hit paintballs when firing resulting in chop chop and some unecessary wear on the inside
if the bolt pin is against the rear part of the hammer you should hear a slight click when closing the breech, just a slight resistance then it is set perfect.
usually it stays there for some while but you can also use locktite (blue) to keep the ram in place.

titocampos1990 · August 4th, 07:30 AM

ok, but will the manuel with the gun or the ram adjuster tell me how to do it?

**DaBluedevil** · August 4th, 09:51 AM

Yes. The manual is great, full color and tons of pictures.

Thread Tools

View more Paintball photos