[russianden]

Lookin to buy your broken or used guns.

Post your offer with a description of your gun and any problems that it may have, and I will give you a price for it.

Prices:
Smart Parts Ion: 100 +/-
Smart Parts Shocker: 250 +/-
Egos: 350 +/-
Promasters: 140 +/-
Intimidators: 200 +/-
Invert Minis: 250 +/-
Tippmann: 50 +/-
DM4: 220 +/-
DM5: 250 +/-
DM6: 300 +/-
PM5: 220 +/-
PM6: 270 +/-
PM7: 350 +/-

All of the prices are negotiable and will vary depending on the upgrades.

Rules:
No flaming
Post here before PMing

[DevinHiNoon]

I have an ICD 2004 BKO with 2k6 Chaos, Vapor Valve, Vapor Bolt, and brand new Evil Detonator regulator (all together is $200+ in upgrades). Today I went to play some at the local field and I was adjusting the lpr and regulator to get it tweeked perfectly. Well one of the screws on the grip frame came out and when I was putting it back in I forgot to check for wires that may have slipped out. Sure enough the two connecting the soleniod did. Some how they completely came out rather than being pinched. I could solder them back in place but I could really care less since I'm selling the gun anyway. It shouldn't be that hard to fix, just solder them back, other than that it's a great gun, tons of modes and pretty accurate. It can reach 25+ bps with the Chaos. Vaporworks will put eyes in the gun for $90.00, then it will have no limit on the speed. Overall it's a good back up gun if you have like a Shocker or matrix, it's equal if not better than most $500-$600 guns like timmy's, ions, mini's, even some cheap shockers.

[Nor*Tex]

Check my sig.

[Kleivonen]

Shocker in sig. Needs new reg and new Vertical adaptor. 295


LMK

[sickCHROMEmag]

spyder 2000...frame is missing a screw that runs up through the grip and the white plastic inside it and finally into the back of the trigger guard...aside from that, there's a round piece that screws onto the bolt and you pull it to cock the gun, but it's missing...gun still cocks, just gotta do it with the bolt itself...20" stone cold sniper barrel (3 piece) plus stock barrel...

32 degrees rebel xtreme...everything is fine except the screw that goes into the gun and pinches the sight rail on and also holds the bolt and internals inside the gun - it got broken or lost or something and replaced with a hardware store screw and washer and wing nut...stock 12" barrel as well as an aftermarket 32 degrees 12" barrel

also have a few packs with pods and a wide variety of co2 tanks...couple sets of goggles and a remote hose...hopper...elbow...the works

[AtomixImpy13]

Smart Parts Nerve, LNIB w/ NDZ ASA

[cspaintball]

wgp superstock has a small leak out the noid

[skinner]

i have a blue 2004 bko noid is junk 50 bucks its yours

[ross_jenkins3]

I have a Silver Pm6 that has been used like 4 cases very good shape have lots of things that could give with it (max flo,other tank,bag,mask) PM ME

[ross_jenkins3]

Also has trigger on it and UL.

[Titus]

Tippmann Prolite, leaks down the barrel, needs an oring. PM if interested

[dave88ia]

like new rebel le, needs valve o-ring and new bolt pull pin... well pm me if interested

[smartparts_2011]

promaster with tadao board and infinity asa, pm if intrested, around 200 obo

[scottevil907]

iv got a leaking dm5.. easy fix, simple oring fix for the bolt..
dm5 is a red to black fade... ups are, tadao m3 board, clamping feedneck, ndz on/off with rail.. iv got pics if your serious and come with a serious offer..

[jmoore89]

I have two Tippman Custom 98's. They've just been sitting in my garage. Last time I fired them, they were in working order but it's been two years. I'd be willing to sell them for $30 each. Pictures can be sent as well.

[jmoore89]

Correction: I have four Tippman Custom 98's, one with a flatline barrel system attached. I also have a PMI Black Maxx. Let me know if you are interested in pictures.