FAQ and info - Paintball Forum - Paintball guns and gear forums

Reply

Old August 8th, 2007, 08:54 PM   #1 (permalink)
bow chicka
 
evolkers2003's Avatar
 
Join Date: Dec 2005
Location: Wisconsin, no city though, you e-rapist
Posts: 2,640
FAQ and info

Basic facts and info:

THE FUSION CAN USE LP OR HP! But HP is recommended.
1. The fusion used autococker barrel threads.


2. DP's customer service: [email protected]


3. The recommended operating pressure for a fusion is 250 psi.


4. How do I know if the eyes are working? The LED on the side, that you can see through the grip, will turn solid blue.


5. If your battery is low, the LED on the side of the grips will blink red.


6. If the LED is blue and there is no ball in the breech, open up the grip frame and make sure that the plug with 4 wires is conected.


7. The eyes and detents are located on the side of the gun, under the eye covers.


8. The serial number is located at the bottom side of the trigger guard.


9. If your Fusion can not keep a consistently high velocity, check your HPR (OPR in the manual). Check all o-rings and clean and lube everything. The fusion is known to need good service to the OPR for good results from the gun. If you notice the regulator start to creep up, and exceeds 300 psi, do not use the gun. Service the reg, especially parts #34 and #27.


10. RAP (you might have heard this when talking about your on/off) stands for Rapid air pressurizing system, and its the fusions quick lever on/off.

11. Dangerous power carries a 1 year warranty on their fusion markers from the date bought.

12. DOW 55 lube is the best to use with your fusion, but Dow 33 based lubes will also work. DO NOT lube your bolt. Its delrin and it is 'self lubricating', plus delrin has been known to swell up which will cause major problems for you.
__________________
Sex on tv cant hurt unless you fall off.

West WI? Play at Combat paintball.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by evolkers2003; August 9th, 2007 at 08:57 PM..
evolkers2003 is offline View My Blog!   Reply With Quote
Sponsored Links
Advertisement
 
Old August 8th, 2007, 08:55 PM   #2 (permalink)
bow chicka
 
evolkers2003's Avatar
 
Join Date: Dec 2005
Location: Wisconsin, no city though, you e-rapist
Posts: 2,640
Maintenece

Use dow 55 lube (or a dow 33 based lube if dow 55 isnt available) on your fusion. DO NOT lube the bolt.


External maintenece
When cleaning your fusion, a damp (but not soaking) rag can usually get most of th edirt and grime off the outside. Use Q-tips to get into small spots.


Bolt
You do not need to lubricate the bolt at all. Just wipe the bolt down and dry it off occasionally. Some manuals have a miss print that says there are o-rings on your bolt, there are in fact no o-rings so dont get your panties in a bundle.

To take the bolt out, pull up on the pin that connects the bolt to the lower tube. Then pull the bolt out the rear of the gun. Wipe the bolt down, then re-insert it back into the body. A small amount of oil can be used on the pin to keep it sliding in and out of the bolt nicely.


Striker
Here is a break down on how to take your fusions striker out and clean it:
~Lift up the locking pin and turn the cylinder 90 degrees, then pull the striker and main pin out.
~Pull the striker out from the ram cap. Lube the back two o-rings of the striker with gel type lube. If they look badly worn or cut then replace them.


Eyes
If your eye sensors are dirty it wont read paint, and that will probably cause some frustration for you. Here is how to clean them:
~Remove eye covers from the side of the gun.
~Be careful, and pull the eyes out. Wipe down the eyes (and detents if you want, since your right there)with a cotton swab.
~Put the eye sensor (and detents) back in, and re-attach eye eye covers.


Firing valve
~Remove your asa and your hoses. Also remove the two screws on the top and bottom of the grip.
~Disconnect your eye wires and solenoid line, then disconnect the grip frame from the body.
~Turn the firing valve screw (found under the body) counter clockwise.
~Push the firing valve out of the body with a tool of some sort.
~Perform basic maintenance and re-insert back into the body. Re-assemble the gun.
__________________
Sex on tv cant hurt unless you fall off.

West WI? Play at Combat paintball.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by evolkers2003; August 9th, 2007 at 09:18 PM..
evolkers2003 is offline View My Blog!   Reply With Quote
Old August 8th, 2007, 08:55 PM   #3 (permalink)
bow chicka
 
evolkers2003's Avatar
 
Join Date: Dec 2005
Location: Wisconsin, no city though, you e-rapist
Posts: 2,640
Trouble shooting your fusion

Here is some common problems and how to fix them:

Q: My fusion will not fire when my eyes are on:
A: 1. There is no ball in the breech.
2. Broken paint inside
3. Dirty eyes


Q: The pressure gauge will not move on my fusion.
A: The gauge is broken. Either it got hit hard, or you over pressurized the gun and broke it. Buy a new one.


Q: My fusion will not fire
A: 1. Turn the gun on
2. FIll your air tank and make sure the on/off is on.
3. Replace battery
4. Re-adjust trigger so its farther out.
5. Make sure your eye sensor is working, and there is paint in the breech if its on.
6. Adjust your pressure in your regs. Adjust the lpr if your OPR is set at 250.


Q: My fusion wont even turn on!
A: 1. Hold down button longer
2. The battery has come unconnected, or the battery wire is coming off. Either re-conect the battery or re-attach the battery cable.


Q: My fusion is leaking from the barrel
A: 1. Your valve pin is in the incorrect position. Remove the lpr and re-grease the spring and valve pin.
2. Your valve pin is worn and need to be replaced.


Q: My fusion is chopping paint.
A: 1. You need new ball detents.
2. Change battery
3. Make sure the eyes are clean.
4. Pressure is set too high in one of the regs


Q: My fusion wont cycle
A: 1. Your air pressure might be low. Re-fill your air tank, or adjust pressure in the regs.
2. Replace battery
3. Replace striker o-ring, or if it still persists replace the whole striker.
__________________
Sex on tv cant hurt unless you fall off.

West WI? Play at Combat paintball.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by evolkers2003; August 9th, 2007 at 09:31 PM..
evolkers2003 is offline View My Blog!   Reply With Quote
Sponsored Links
Advertisement
 
Old August 8th, 2007, 08:56 PM   #4 (permalink)
bow chicka
 
evolkers2003's Avatar
 
Join Date: Dec 2005
Location: Wisconsin, no city though, you e-rapist
Posts: 2,640
Your fusion board

Open the left side of the grips(guage side). Look inside on the circuit board(also called the PC board). On the stock 20bps board, you will have a little box with two switches labeled "1" and "2." The newer boards with 25bps and Full Modes will have the same box on the same side, but with 4 switches labeled 1-4. Following are the configurations needed to be set for the respected modes.

The top battery on the back is the universal power button. The lower one is the eye button which is used to turn the eyes on and off. Also if you dont use your fusion for 20 minutes the gun will turn off.

To turn the gun on, hold the power button down. TO turn it off do the same. To turn the eyes off hold down the eye button, do the same to turn them back on. The fusion always starts up with the eyes on.

Quick reference guide for your board:
Red light flashes every 3 seconds- Your battery is low, replace your battery.
Red light flashes every 5 seconds- standby mode, it kicks in automatically after about 30 seconds.
Blue light is a solid blue- Sensor system is on, and the marker has balls in it.
Blue light is blinking rapidly- Your eyes are off
Blue light is blinking slowly- The eyes are on and the marker dies not have any paint in it.
__________________
Sex on tv cant hurt unless you fall off.

West WI? Play at Combat paintball.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by evolkers2003; August 9th, 2007 at 09:38 PM..
evolkers2003 is offline View My Blog!   Reply With Quote
Old August 8th, 2007, 08:56 PM   #5 (permalink)
bow chicka
 
evolkers2003's Avatar
 
Join Date: Dec 2005
Location: Wisconsin, no city though, you e-rapist
Posts: 2,640
Adjusting your velocity:

First things first, here is a step by step manual to setting the velocity on your fusion:

1. Turn all your regs to 0 psi. Thats right, turn the OPR clockwise (tighten it in, this restricts air flow into the opr) if you are looking straight down at it. Also turn your LPR (under the barrel) all the way in.

2. Air up the gun. The gauge above the HPR should read 0.

3. Set your OPR to about 250. THis can be slightly tricky as when you fire the gun the needle will rise for a bit. Set it maybe just above 200 psi. DO NOT let the gauge exceed 300 psi.

4. Turn the gun on, notice it wont cycle. Turn the LPR out until the marker fully cycles.

5. Go to the chrono. Adjust your lpr until the gun is at your desired fps.

NOTE: The gun WILL leak when you have your OPR and LPR all the way in. This is because there is not enough air have the noid seal. If the gun is leaking after you set the HPR to 250 you may have problems.

Last edited by evolkers2003; August 9th, 2007 at 09:46 PM..
evolkers2003 is offline View My Blog!   Reply With Quote
Old August 8th, 2007, 08:57 PM   #6 (permalink)
bow chicka
 
evolkers2003's Avatar
 
Join Date: Dec 2005
Location: Wisconsin, no city though, you e-rapist
Posts: 2,640
Leaks in your fusion:

If your gun is leaking from the OPR/LPR adjustment screws:

1. Snap out the snap clips and take the adjustment screws out. Relube the o-rings with dow 55 or replace the o-rings.

LPR:

1. Re-lube or replace 4 outer o-rings in the LPR.

The small screw under the LPR:

1. Put loctite on it and put it in flush to the body.

Noid:

1. Needs to be rebuilt. Contact DP.
__________________
Sex on tv cant hurt unless you fall off.

West WI? Play at Combat paintball.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by evolkers2003; August 9th, 2007 at 09:51 PM..
evolkers2003 is offline View My Blog!   Reply With Quote
Old August 8th, 2007, 08:58 PM   #7 (permalink)
bow chicka
 
evolkers2003's Avatar
 
Join Date: Dec 2005
Location: Wisconsin, no city though, you e-rapist
Posts: 2,640
I, nor any one else on PBF, is responsible for damage done to your gun! Also all forum rules apply in here!
__________________
Sex on tv cant hurt unless you fall off.

West WI? Play at Combat paintball.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by evolkers2003; August 9th, 2007 at 09:53 PM..
evolkers2003 is offline View My Blog!   Reply With Quote
Old August 8th, 2007, 09:05 PM   #8 (permalink)
<a href="http://www.picoo
 
kant_think's Avatar
 
Join Date: Jan 2005
Location: Arizona
Posts: 3,251
Excellent post.

Sticky this
__________________
X-Box live: KhaoticKiwi
kant_think is offline View My Blog!   Reply With Quote
Old August 8th, 2007, 10:54 PM   #9 (permalink)
Imperator
 
Dooms's Avatar
 
Join Date: Jul 1992
Location: I'm all over.
Posts: 19,071
Blog Entries: 1
Do you have permission from "yougotowned" and "luck4143" to repost here? If you get it I'll sticky it.



__________________
2003 Summer Super Moderator and Most Informative Award Winner

COG/TOG Member

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Dooms is offline View My Blog!   Reply With Quote
Old August 9th, 2007, 01:20 PM   #10 (permalink)
bow chicka
 
evolkers2003's Avatar
 
Join Date: Dec 2005
Location: Wisconsin, no city though, you e-rapist
Posts: 2,640
Quote:
Originally Posted by doomsday View Post
Do you have permission from "yougotowned" and "luck4143" to repost here? If you get it I'll sticky it.
Ok, i'll talk to them. It might be hard since some of them have been banned and stuff. If i cant get it, i will wright a new one up in my own words and my own material.
__________________
Sex on tv cant hurt unless you fall off.

West WI? Play at Combat paintball.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
evolkers2003 is offline View My Blog!   Reply With Quote
Old August 9th, 2007, 09:55 PM   #11 (permalink)
bow chicka
 
evolkers2003's Avatar
 
Join Date: Dec 2005
Location: Wisconsin, no city though, you e-rapist
Posts: 2,640
Pk, i pretty much re-typed the whole thing. That was a chore

I modeled it a lot after what i had before, and made sure i covered the same things as the other posts to make sure we had everything in here. Hope this fits the requirements of dooms
__________________
Sex on tv cant hurt unless you fall off.

West WI? Play at Combat paintball.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
evolkers2003 is offline View My Blog!   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


VerticalSports
Baseball Forum Golf Forum Boxing Forum Snowmobile Forum
Basketball Forum Soccer Forum MMA Forum PWC Forum
Football Forum Cricket Forum Wrestling Forum ATV Forum
Hockey Forum Volleyball Forum Paintball Forum Snowboarding Forum
Tennis Forum Rugby Forums Lacrosse Forum Skiing Forums
Copyright (C) Verticalscope Inc Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc. Search Engine Optimization by vBSEO 3.6.1