Nightmare...UpKeep - Paintball Forum - Paintball guns and gear forums

Reply

Old July 30th, 2004, 08:36 PM   #1 (permalink)
\/ My First avitar \/
 
KidPaintball's Avatar
 
Join Date: Jul 2003
Location: New York
Posts: 1,673
Nightmare...UpKeep

What should I do to keep it in working order. I have no clue how to open it so some help would be good.

What are some general oldschool gideline?
__________________
-Niagara Hustle - 07
-rockland Hustle - 08

|PM7|

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


"Read. Comprehend. Post."
KidPaintball is offline View My Blog!   Reply With Quote
Sponsored Links
Advertisement
 
Old July 30th, 2004, 09:03 PM   #2 (permalink)
D_Smalls
Guest
 
Posts: n/a
contact nick.. his screen name on pbf is BUBBASR, he owns one, if hes not busy pimping he'll probably help ya
View My Blog!   Reply With Quote
Old July 30th, 2004, 10:10 PM   #3 (permalink)
\/ My First avitar \/
 
KidPaintball's Avatar
 
Join Date: Jul 2003
Location: New York
Posts: 1,673
Cool, he mods the Rateing section right? I'll give it a shot! (Pun intended)
__________________
-Niagara Hustle - 07
-rockland Hustle - 08

|PM7|

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


"Read. Comprehend. Post."
KidPaintball is offline View My Blog!   Reply With Quote
Sponsored Links
Advertisement
 
Old August 12th, 2004, 12:32 AM   #4 (permalink)
 
Join Date: Jul 2004
Posts: 53
I own a lot of nightmares. 4 to be exact. Just clean them once in a while. To take apart its very simple. Leave the whole upper half of the gun alone (puncture pin...). Next take off pump arm (unscrew screws that go into the bolt and hammer). Next take off the frame. Then unscrew set screws that hold in valve. Next pop out the back piece and everything should slide out of the gun. You may have to tap the valve with an allen wrench or something to get it out. Run squeegee through the gun. Wipe parts clean. Do not disassemble the valve. Just wipe it off. Reoil everything and put back together. Make sure to oil the pump arm.

These guns shoot a lot better if you polish the internals. To do this, rub with neverdull and if ruff surface, sand with croakus cloth and oil. Then rub with neverdull. If surface is rusty, make sure all seals are removed and soak part in CLR, wipe clean, oil, rub with croakus cloth till surface is smooth, wipe clean, rub with neverdull till shiny and polished. Then wipe with clean cloth. Make sure to rub inside of all holes (set screw and screw holes) with neverdull and wipe clean with paper towel. Soak screws in CLR and wipe with neverdull to remove rust and grime. Then let parts sit for a night. Then oil all parts, oil o-rings, and put back together.
Biggy is offline View My Blog!   Reply With Quote
Old August 24th, 2004, 09:21 PM   #5 (permalink)
\/ My First avitar \/
 
KidPaintball's Avatar
 
Join Date: Jul 2003
Location: New York
Posts: 1,673
How/ what size of soemthing do I use to get the valve out?
__________________
-Niagara Hustle - 07
-rockland Hustle - 08

|PM7|

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


"Read. Comprehend. Post."
KidPaintball is offline View My Blog!   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


VerticalSports
Baseball Forum Golf Forum Boxing Forum Snowmobile Forum
Basketball Forum Soccer Forum MMA Forum PWC Forum
Football Forum Cricket Forum Wrestling Forum ATV Forum
Hockey Forum Volleyball Forum Paintball Forum Snowboarding Forum
Tennis Forum Rugby Forums Lacrosse Forum Skiing Forums
Copyright (C) Verticalscope Inc Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc. Search Engine Optimization by vBSEO 3.6.1