Paintball Guns and Gear forums banner

1 - 9 of 9 Posts

·
Registered
Joined
·
116 Posts
Discussion Starter #1
ok so i just got my gun back form Generation E all fixed and i go to play today and just everything goes wrong...so i sat around for 4 hours watching...

what could i do to make my gun haver lower pressure,more accurate,break less orings?

im thinking an Ultralight 16 in barrel, LP tank,evovle bolt kit?? i dotn want to spend all that money though. its 150 for a bolt kit at my local shop
 

·
Banned
Joined
·
2,324 Posts
lp tank wont lower the pressure going into your gun, just the pressure going into your hpr, sweetspot you regs, new barrel will help your accuracy, you could also get a cp reg thatll keep your gun more consistent helping accuracy, and just keep ur orings lubed with some slick honey, also dont get an evolve unless u can get it from 150, you could get a ff bolt, and c4 mod and you'll get evolve-like efficiency
 

·
Registered
Joined
·
116 Posts
Discussion Starter #3
sorry but what do you mean by sweetspot the regs? like set it perfectly?

also the only reason i was thinking evolve is becasue i heard you dont break orings and its just better quality

also the FF bolt...thats not kit right? its just the bolt part that all the other stuff slips in too?
 

·
Banned
Joined
·
2,324 Posts
basically he's breakin o-rings, wants to lower his operating pressure, and better accuracy.

sweetspot your regs, thatll help get your regs set at the right spot, this give u more consistency helping accuracy, better efficiency and will get your pressure at the right spot.
keep all ur orings lubed, slick honey is the best lube for trixes thatll keep your o-rings lasting longer and reduce friction so you can lower ur lpr reducing bolt pressure.]
lastly get a stiffi switch kit if you have the cash,awesome kit
 

·
Registered
Joined
·
116 Posts
Discussion Starter #6
one of the problems was that my LCD screen was like detaching from the board and stuff when i was dry firing.
 

·
Registered
Joined
·
116 Posts
Discussion Starter #9
yea sry i was le tired so i didnt feel like posting it all...

PROBLEM 1: After my third or fourth game i decided to dry fire off the rest of my air for fun. So all of a sudden it stops shooting so i check my air and theres still some left,then i look at my LCD screen and its frozen...becasue it still said Pow! even when i wasnt holding the trigger (it says Pow! under the BPS on my LCD whenever i pull the trigger) so i bring it over to the people who work at the field and he took it apart and saw that the LCD screen was like disconnected from my board and froze. but if you held the screen down it would work fine so he put folded up paper under the grips to hold it down in place...that took him about an hour to figure it out

PROBLEM TWO: I get on the field and my gun wont feed balls...turns out i left my halo on while i went to go get my gun fixed so it ran out of batteries...then i had to go buy batteries. So i get up to the place where you buy them and nobody is there...everyone was playing in a rec game so i had to wait like 15 minutes just to buy batteries. So that fixed the feeding problem.

PROBLEM 3: I go on the field again to play and off the break and when i walked the trigger the balls just started dropping like the tank stoped feeding it air... so i brought it back up to the guy that worked there and he couldnt get it to stop..he set the LPR and reg like 3 times and stuff...never got that to stop happening. So i went to the chrono place and tried to shoot it and it wouldnt even shoot anything...it was aired up and all it did was click like i was messing with it with no tank....i had a full tank too. So by this time the day was over and i had to pack up.

also i had to replace 4 orings in the bolt that day..but thats just normal i guess

and now im Le depressed =(

the main thing i want to know is how i fix the third problem where it would just starting stop feeding air to the gun it seemed.
 
1 - 9 of 9 Posts
Top